...
10. Run `vcpe.py infra`
11. Make sure sniro configuration is run as part of the above step.
12. Install curl command inside sdnc-sdnc-0 container
13. Run `healthcheck-k8s.py onap` to check connectivity from sdnc to brg and gmux. If healthcheck-k8s.sh fails, check /opt/config/sdnc_ip.txt to see it has the SDNC host ip correctly. If you need to change SDNC host ip, you need to clean up and rerun `vcpe.py infra`.
Also verify tap interfaces tap-0 and tap-1 are up by running vppctl with show int command. If tap interfaces are not up, use vppctl tap delete tap-0 and tap-1 and then run `/opt/bind_nic.sh` followed by `/opt/set_nat.sh`.
...
.
If you have changed the SDNC_IP after instantiation of the vBNG and vBRGEMU:
- you need to also update the /opt/sdnc_ip in the vBNG and run v_bng_install.sh to get the vBNG route tables updated.
- you need to change sdnc_ip.txt and
...
- ip.txt
...
- on the vBRGEMU
| Code Block | ||||
|---|---|---|---|---|
| ||||
root@zdcpe1cpe01brgemu01-201812261515:~# vppctl tap delete tap-0
Deleted.
root@zdcpe1cpe01brgemu01-201812261515:~# vppctl tap delete tap-1
Deleted.
[WAIT A FEW SECONDS BEFORE DOING NEXT STEPS or you may get an error since vppctl lstack returns error.]
root@zdcpe1cpe01brgemu01-201812261515:~# /opt/bind_nic.sh
root@zdcpe1cpe01brgemu01-201812261515:~# /opt/set_nat.sh
root@zdcpe1cpe01brgemu01-201812261515:~# vppctl show int
Name Idx State Counter Count
GigabitEthernet0/4/0 1 up tx packets 12
tx bytes 3912
local0 0 down
tap-0 2 up rx packets 5
rx bytes 410
drops 7
ip6 1
tap-1 3 up rx packets 1
rx bytes 70
drops 7
ip6 1 |
...
25. If SDNC needs to be redeployed, you need again to distribute service model from SDC UI, create ip pool, install curl, and set SDNC VM cluster node routing table. Then you should reinstantiate infra VNFs, otherwise you would need to change sdnc ip address in VNFs for snat config.
Checklist for Dublin
...
and El Alto Releases
- Model distribution by `demo-k8s.sh onap init`. this will onboard VNFs and 4 services, i.e. infrastructure, brg, bng and gmux
- Run Robot `ete-k8s.sh onap distributevCPEResCust`. This step assumes step 1 successfully distributed the 4 models
- Add customer SDN-ETHERNET-INTERNET (need to put into vcpe init)
- Add identity-url to RegionOne
- Add route on sdnc cluster node `ip route add 10.3.0.0/24 via 10.0.101.10 dev ens3`
- Initialize SDNC ip pool by running from Rancher node `kubectl -n onap exec -it dev-sdnc-sdnc-0 -- /opt/sdnc/bin/addIpAddresses.sh VGW 10.5.0 22 250`
- Install python and other python libraries
- In El Alto this can be done via ~integration/test/vcpe/bin/setup.sh
- Change the openstack env parameters and the customer service related parameter in vcpecommon.pyin vcpecommon.py
- Make sure to Change vgw_VfModuleModelInvariantUuid in vcpecommon.py based on the CSAR - it changes for every CSAR
- Run `vcpe.py init`
- Insert a the custom service workflow entry in SO catalogdb
...
16. Start closeloop by `./vcpe.py loop` to trigger packet drop VES event. You may need to run the command twice if the first run fails
[Note you may need to comment out the set_closed_loop in vcpe.py line 165 if
| Jira | ||||||
|---|---|---|---|---|---|---|
|
#vcpecommon.set_closed_loop_policy(policy_template_file)
| Code Block | ||||
|---|---|---|---|---|
| ||||
[2019-06-04 11:03:49,822][INFO ][pool-5-thread-20][org.onap.dcae.common.EventProcessor] - QueueSize:0 EventProcessor Removing element: {"VESversion":"v5","VESuniqueId":"88f3548c-1a93-4f1d-8a2a-001f8d4a2aea","event":{"commonEventHeader":{"startEpochMicrosec":1559646219672586,"sourceId":"d92444f5-1985-4e15-807e-b8de2d96e489","eventId":"Generic_traffic","reportingEntityId":"No UUID available","eventType":"HTTP request rate","priority":"Normal","version":1.2,"reportingEntityName":"zdcpe1cpe01mux01-201906032354","sequence":9,"domain":"measurementsForVfScaling","lastEpochMicrosec":1559646229672586,"eventName":"Measurement_vGMUX","sourceName":"vcpe_vnf_vcpe_vgmux_201906032354"},"measurementsForVfScalingFields":{"cpuUsageArray":[{"percentUsage":0,"cpuIdentifier":"cpu1","cpuIdle":100,"cpuUsageSystem":0,"cpuUsageUser":0}],"measurementInterval":10,"requestRate":492,"vNicUsageArray":[{"transmittedOctetsDelta":0,"receivedTotalPacketsDelta":0,"vNicIdentifier":"eth0","valuesAreSuspect":"true","transmittedTotalPacketsDelta":0,"receivedOctetsDelta":0}],"measurementsForVfScalingVersion":2.1,"additionalMeasurements":[{"name":"ONAP-DCAE","arrayOfFields":[{"name":"Packet-Loss-Rate","value":"22.0"}]}]}}} |
17. Stop cloed loop for testing with ./vcpe.py noloss
Frankfurt vCPE.py Log for creating networks:
View file name vcpe.20200625.log height 250
Typical Errors and Solutions
...